Get free quotes

Calculator

Vehicle impact energy calculator

How hard a car, bakkie or truck hits a bollard at a given speed, or after a given run-up, set against the ASTM F2656 crash test ratings.

A row of heavy steel security bollards in front of a shopfront

Impact energyCalc sheet BC-VEH-CAL-766, rev C

Speed
Energy at impact
0
Speed
0
Like a fall of
0

ASTM F2656 ratingTest vehicle and speedEnergyCompared
Copies the vehicle, speed and energy into the site plan below.

Choose a vehicle, then enter its speed, or the length of straight it could use to pick up speed towards the line. The energy, the speed and the matching ratings update as you type.

How the impact calculator works

It works out the kinetic energy of the vehicle: energy = ½ x mass x speed², with the speed in metres a second. If you choose the run-up, it works out the speed a vehicle could reach from standstill over that distance at a steady average acceleration: speed = √(2 x acceleration x distance). The accelerations are rough full-throttle averages (about 3 m/s² for a car, 2.5 for a bakkie, 1.5 for a medium truck and 0.8 for a heavy truck); change them if you know better. "Like a fall of" is the height a vehicle would have to drop to hit the ground at the same speed.

The table compares your figure with the ASTM F2656 test vehicles and speeds. It marks the lowest rating tested with a vehicle at least as heavy, carrying at least as much energy. That is a guide to the range, not a design.

ASTM F2656 vehicle ratings

The rating is the vehicle class and the test speed in miles an hour, then a penetration rating: P1 is 1 m or less past the line, P2 up to 7 m, P3 up to 30 m and P4 more than 30 m.

RatingTest vehicleSpeedEnergy
C40Small car, 1 100 kg64 km/h176 kJ
C50Small car, 1 100 kg80 km/h275 kJ
C60Small car, 1 100 kg97 km/h396 kJ
PU40Pickup (bakkie), 2 300 kg64 km/h368 kJ
PU50Pickup (bakkie), 2 300 kg80 km/h575 kJ
PU60Pickup (bakkie), 2 300 kg97 km/h827 kJ
M30Medium duty truck, 6 800 kg48 km/h612 kJ
M40Medium duty truck, 6 800 kg64 km/h1.09 MJ
M50Medium duty truck, 6 800 kg80 km/h1.70 MJ
H30Heavy goods truck, 29 500 kg48 km/h2.65 MJ
H40Heavy goods truck, 29 500 kg64 km/h4.72 MJ
H50Heavy goods truck, 29 500 kg80 km/h7.37 MJ

Energy worked out from the test mass and speed. Standards are revised from time to time; check the edition on the test certificate.

What this means for your site

  • Most plastic, surface-bolted and decorative bollards guide and deter; they are not built for this kind of energy.
  • A steel or concrete post in a proper footing stops a car at low speed. For ram raids and crowded spaces, ask for a tested design.
  • Cut the run-up where you can: a bend, a kerb, planters or a change of level all lower the speed a vehicle can reach.
  • The footing is part of the rating. Check services early; shallow foundation designs exist. See the footing calculator.

Frequently asked questions

How much energy does a car have when it hits a bollard?
Kinetic energy is half the mass times the speed squared. A 1,500 kg car at 50 km/h (13.9 m/s) carries about 145 kJ; the same car at 100 km/h carries four times as much, about 580 kJ. A 6,800 kg truck at 48 km/h, the ASTM F2656 M30 test, carries about 610 kJ.
What does M30 mean on a bollard?
M30 is an ASTM F2656 crash test rating: the bollard stopped a 6,800 kg medium duty truck at 30 mph (about 48 km/h). M40 and M50 are the same truck at about 64 and 80 km/h. A penetration rating follows, such as P1, for how far the front of the truck went past the line (P1 is 1 m or less). Other standards, such as PAS 68 and IWA 14-1, rate in their own way.
Why does the run-up matter?
A vehicle can only hit as fast as it can accelerate in the space it has. Speed grows with the square root of the run-up, and energy grows with the run-up itself, so a long straight approach to a shopfront needs a much stronger barrier than a tight corner. Designers use this to choose a rating, and add bends, planters or kerbs to cut the approach speed.
Can I use the energy to choose a bollard myself?
Use it to see the range you are in and to ask the right questions. A crash rating is for one tested design, footing and vehicle, installed to the maker's drawing; a bollard with a higher energy figure on paper is not rated unless it was tested. Ask for the test certificate. See anti-ram bollards and security bollards.

Free quote request, no obligation

Ask for rated bollard quotes

Draw up the site plan the way an installer would: what you are protecting, the length or the openings, the ground, where you are and how soon. Suppliers and installers in your area quote you directly.

Site planAnti-Ram and Crash-Rated Bollards
Request
No. 47107
Rev
A, for quote
Drawn
2026-11-22

1The job

2Set out the line (optional, it helps the quote)

Plan view: the lineN ↑

-
-
-
-
-
-
Estimate
-

A rule of thumb, not a quote.

3Stage, ground and timing

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: posts, lights, gates, humps, barriers or cones.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable suppliers and installers. See our privacy policy.

Get free bollard quotes