Get free quotes

Calculator

Bollard spacing calculator

Work out how many bollards a line or an entrance needs, the centre spacing to set out and the clear gap left between the posts. Drawn to scale as you type.

A line of steel bollards evenly spaced along the edge of a parking area

Spacing and countCalc sheet BC-BOL-CAL-215, rev G

What are you closing off?
From the centre of the first post to the centre of the last.
Many designers use about 1,200 mm: cars are stopped, people, prams and wheelchairs get through.
Posts
0
Centre spacing
0
Clear gap
0

Plan view, to scale
Copies the length and spacing into the site plan below.

Use the calculation sheet above: choose a line or openings, enter the length or the widths, pick the post and the largest gap you want. The posts, the spacing and the gap update as you type, and the button copies them into your quote request.

How the spacing calculator works

For a line, it takes the length from the centre of the first post to the centre of the last, and the largest clear gap you want. The centre spacing can be no more than the gap plus the post width, so it divides the length by that, rounds up to a whole number of spaces and spreads the posts evenly. Posts = spaces + 1. Because it rounds up, the real gap is a little smaller than the one you asked for, never larger.

For openings between walls, there is a gap at each side, so a width W with posts of width d and a largest gap g needs (W − g) ÷ (g + d) posts, rounded up. The calculator then shares the width evenly between the gaps. For several openings of the same width it multiplies the posts per opening.

Clear gaps at a glance

These are the sort of gaps designers talk about. They are starting points, not rules; a crash-rated design uses the gap it was tested with.

Clear gapWhat it does
About 900 mm to 1,000 mmKeeps out small cars; tight for wheelchairs, prams and delivery trolleys
About 1,200 mmThe gap many designers use: stops cars, lets people through
About 1,500 mmNear the limit: a small car may squeeze through
Over 1,500 mmMarks and guides, but does not reliably keep a car out

Before you set out the line

  • Leave a way through for wheelchairs and prams where people walk, and check that emergency vehicles can still reach the building.
  • Keep the first and last posts close enough to a wall or kerb that a car cannot drive round the end.
  • Check what runs under the line: cables, water and sewer pipes, fibre and gas lines. See bollard installation.
  • On a municipal sidewalk or verge, ask the municipality first; work in the road reserve usually needs a wayleave.
  • Then work out the concrete with the footing calculator.

Frequently asked questions

How far apart should bollards be?
Many designers leave a clear gap of about 1.2 m between bollards. That stops cars while pedestrians, prams and wheelchairs still get through. Where motorcycles or very small cars must be kept out, the gap is made closer, with a wider way through somewhere nearby. Security designs follow the maker's tested spacing.
What is the difference between the clear gap and the centre spacing?
The clear gap is the space between the faces of two posts, which is what a car or a wheelchair has to pass through. The centre spacing is measured from the middle of one post to the middle of the next, and it is what an installer sets out on site. Centre spacing = clear gap + the post width.
How many bollards do I need for a line?
Divide the length of the line by the centre spacing, round up, and add one for the post at the end. A 12 m line of 114 mm posts with a 1.2 m clear gap has centres of about 1.31 m: 12 ÷ 1.31 is 9.1, rounded up to 10 spaces, so 11 posts.
How many bollards across a driveway or entrance?
Across an opening between two walls, the posts and the gaps share the width: there is a gap at each wall and one between each pair of posts. A 4 m opening with 114 mm posts and a 1.2 m largest gap needs 3 posts, leaving gaps of about 914 mm. For an entrance that must open, look at removable, fold-down or retractable bollards.

Free quote request, no obligation

Send your line for quotes

Draw up the site plan the way an installer would: what you are protecting, the length or the openings, the ground, where you are and how soon. Suppliers and installers in your area quote you directly.

Site planBollards
Request
No. 50329
Rev
A, for quote
Drawn
2026-11-22

1The job

2Set out the line (optional, it helps the quote)

Plan view: the lineN ↑

-
-
-
-
-
-
Estimate
-

A rule of thumb, not a quote.

3Stage, ground and timing

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: posts, lights, gates, humps, barriers or cones.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable suppliers and installers. See our privacy policy.

Get free bollard quotes